View MC74HC4017_9046510.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

semiconductor technical data 1 rev 6 ? motorola, inc. 1995 10/95 highperformance silicongate cmos the m c74hc401 7 i s i dentica l i n p inou t t o t h e s tandar d c mos mc14017b. the device inputs are compatible with standard cmos outputs; with pullup resistors, they are compatible with lsttl outputs. the hc4017 uses a five stage johnson counter and decoding logic to provide highspeed operation. this device also has an activehigh, as well as activelow clock input. ? output drive capability: 10 lsttl loads ? outputs directly interface to cmos, nmos, and ttl ? operating voltage range: 2 to 6 v ? low input current: 1 m a ? high noise immunity characteristic of cmos devices ? in compliance with the requirements defined by jedec standard no. 7a ? chip complexity: 176 fets or 44 equivalent gates logic diagram decade outputs pin 16 = v cc pin 8 = gnd clock enable carry out reset clock q0 q1 q2 q3 q4 q5 q6 q7 q8 q9 15 3 2 4 7 1 5 6 9 14 13 11 12 10 pin assignment 13 14 15 16 9 10 11 12 5 4 3 2 1 8 7 6 carry out clock enable clock reset v cc q8 q4 q9 q2 q0 q1 q5 gnd q3 q7 q6 d suffix soic package case 751b05 n suffix plastic package case 64808 1 16 1 16 ordering information mc74hcxxxxn mc74hcxxxxd plastic soic
MC74HC4017 motorola highspeed cmos logic data dl129 e rev 6 2 ??????????????????????? ??????????????????????? ??????????????????????? ??????????????????????? maximum ratings* ??? ??? ??? ??? symbol ?????????????? ?????????????? ?????????????? ?????????????? parameter ?????? ?????? ?????? ?????? value ??? ??? ??? ??? unit ??? ??? ??? ??? v cc ?????????????? ?????????????? ?????????????? ?????????????? dc supply voltage (referenced to gnd) ?????? ?????? ?????? ?????? 0.5 to + 7.0 ??? ??? ??? ??? v ??? ??? ??? ??? v in ?????????????? ?????????????? ?????????????? ?????????????? dc input voltage (referenced to gnd) ?????? ?????? ?????? ?????? 1.5 to v cc + 1.5 ??? ??? ??? ??? v ??? ??? ??? ??? v out ?????????????? ?????????????? ?????????????? ?????????????? dc output voltage (referenced to gnd) ?????? ?????? ?????? ?????? 0.5 to v cc + 0.5 ??? ??? ??? ??? v ??? ??? ??? ??? i in ?????????????? ?????????????? ?????????????? ?????????????? dc input current, per pin ?????? ?????? ?????? ?????? 20 ??? ??? ??? ??? ma ??? ??? ??? ??? i out ?????????????? ?????????????? ?????????????? ?????????????? dc output current, per pin ?????? ?????? ?????? ?????? 25 ??? ??? ??? ??? ma ??? ??? ??? ??? i cc ?????????????? ?????????????? ?????????????? ?????????????? dc supply current, v cc and gnd pins ?????? ?????? ?????? ?????? 50 ??? ??? ??? ??? ma ??? ??? ??? ??? ??? p d ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? power dissipation in still air plastic dip2 soic package2 ?????? ?????? ?????? ?????? ?????? 750 500 ??? ??? ??? ??? ??? mw ??? ??? ??? ??? t stg ?????????????? ?????????????? ?????????????? ?????????????? storage temperature ?????? ?????? ?????? ?????? 65 to + 150 ??? ??? ??? ??? c ??? ??? ??? ??? ??? t l ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? lead t emperature, 1 mm from case for 10 seconds (plastic dip or soic package) ?????? ?????? ?????? ?????? ?????? 260 ??? ??? ??? ??? ??? c * maximum ratings are those values beyond which damage to the device may occur . functional operation should be restricted to the recommended operating conditions. 2derating e plastic dip: 10 mw/ c from 65 to 125 c soic package: 7 mw/ c from 65 to 125 c for high frequency or heavy load considerations, see chapter 2 of the motorola highspeed cmos data book (dl129/d). recommended operating conditions ???? ???? ???? ???? symbol ?????????????? ?????????????? ?????????????? ?????????????? parameter ??? ??? ??? ??? min ??? ??? ??? ??? max ??? ??? ??? ??? unit ???? ???? ???? ???? v cc ?????????????? ?????????????? ?????????????? ?????????????? dc supply voltage (referenced to gnd) ??? ??? ??? ??? 2.0 ??? ??? ??? ??? 6.0 ??? ??? ??? ??? v ???? ???? ???? ???? v in , v out ?????????????? ?????????????? ?????????????? ?????????????? dc input voltage, output voltage (referenced to gnd) ??? ??? ??? ??? 0 ??? ??? ??? ??? v cc ??? ??? ??? ??? v ???? ???? ???? ???? t a ?????????????? ?????????????? ?????????????? ?????????????? operating temperature, all package types ??? ??? ??? ??? 55 ??? ??? ??? ??? + 125 ??? ??? ??? ??? c ???? ???? ???? ???? ???? ???? t r , t f ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? input rise and fall time v cc = 2.0 v (figure 1) v cc = 4.5 v v cc = 6.0 v ??? ??? ??? ??? ??? ??? 0 0 0 ??? ??? ??? ??? ??? ??? 1000 500 400 ??? ??? ??? ??? ??? ??? ns dc electrical characteristics (voltages referenced to gnd) ???? ???? ???? ???? symbol ????????? ????????? ????????? ????????? parameter ????????? ????????? ????????? ????????? test conditions ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? guaranteed limit ??? ??? ??? ??? unit ???? ???? ???? ???? ???? symbol ????????? ????????? ????????? ????????? ????????? parameter ????????? ????????? ????????? ????????? ????????? test conditions ???? ???? ???? ???? ???? v cc v ??? ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? ???? 85 c ???? ???? ???? ???? ???? 125 c ??? ??? ??? ??? ??? unit ???? ???? ???? ???? ???? v ih ????????? ????????? ????????? ????????? ????????? minimum highlevel input voltage ????????? ????????? ????????? ????????? ????????? v out = 0.1 v or v cc 0.1 v |i out | 20 m a ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 1.5 3.15 4.2 ???? ???? ???? ???? ???? 1.5 3.15 4.2 ???? ???? ???? ???? ???? 1.5 3.15 4.2 ??? ??? ??? ??? ??? v ???? ???? ???? ???? ???? v il ????????? ????????? ????????? ????????? ????????? maximum lowlevel input voltage ????????? ????????? ????????? ????????? ????????? v out = 0.1 v or v cc 0.1 v |i out | 20 m a ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 0.3 0.9 1.2 ???? ???? ???? ???? ???? 0.3 0.9 1.2 ???? ???? ???? ???? ???? 0.3 0.9 1.2 ??? ??? ??? ??? ??? v ???? ???? ???? ???? ???? ???? v oh ????????? ????????? ????????? ????????? ????????? ????????? minimum highlevel output voltage ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih or v il |i out | 20 m a ???? ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? ??? 1.9 4.4 5.9 ???? ???? ???? ???? ???? ???? 1.9 4.4 5.9 ???? ???? ???? ???? ???? ???? 1.9 4.4 5.9 ??? ??? ??? ??? ??? ??? v ???? ???? ???? ???? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih or v il |i out | 4.0 ma |i out | 5.2 ma ???? ???? ???? ???? 4.5 6.0 ??? ??? ??? ??? 3.98 5.48 ???? ???? ???? ???? 3.84 5.34 ???? ???? ???? ???? 3.70 5.20 ??? ??? ??? ??? ???? ???? ???? ???? ???? ???? v ol ????????? ????????? ????????? ????????? ????????? ????????? maximum lowlevel output voltage ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih or v il |i out | 20 m a ???? ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? ??? 0.1 0.1 0.1 ???? ???? ???? ???? ???? ???? 0.1 0.1 0.1 ???? ???? ???? ???? ???? ???? 0.1 0.1 0.1 ??? ??? ??? ??? ??? ??? v ???? ???? ???? ???? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih or v il |i out | 4.0 ma |i out | 5.2 ma ???? ???? ???? ???? 4.5 6.0 ??? ??? ??? ??? 0.26 0.26 ???? ???? ???? ???? 0.33 0.33 ???? ???? ???? ???? 0.40 0.40 ??? ??? ??? ??? ???? ???? ???? ???? i in ????????? ????????? ????????? ????????? maximum input leakage current ????????? ????????? ????????? ????????? v in = v cc or gnd ???? ???? ???? ???? 6.0 ??? ??? ??? ??? 0.1 ???? ???? ???? ???? 1.0 ???? ???? ???? ???? 1.0 ??? ??? ??? ??? m a ???? ???? ???? ???? ???? i cc ????????? ????????? ????????? ????????? ????????? maximum quiescent supply current (per package) ????????? ????????? ????????? ????????? ????????? v in = v cc or gnd i out = 0 m a ???? ???? ???? ???? ???? 6.0 ??? ??? ??? ??? ??? 8 ???? ???? ???? ???? ???? 80 ???? ???? ???? ???? ???? 160 ??? ??? ??? ??? ??? m a note: information on typical parametric values can be found in chapter 2 of the motorola highspeed cmos data book (dl129/d). this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however , precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this highimpedance cir - cuit. for proper operation, v in and v out should be constrained to the range gnd (v in or v out ) v cc . unused inputs must always be tied to an appropriate logic voltage level (e.g., either gnd or v cc ). unused outputs must be left open.
MC74HC4017 highspeed cmos logic data dl129 e rev 6 3 motorola ac electrical characteristics (c l = 50 pf, input t r = t f = 6 ns) ???? ???? ???? ???? symbol ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? guaranteed limit ??? ??? ??? ??? unit ???? ???? ???? ???? ???? symbol ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? ???? v cc v ??? ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? ???? 85 c ???? ???? ???? ???? ???? 125 c ??? ??? ??? ??? ??? unit ???? ???? ???? ???? ???? f max ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum clock frequency (50% duty cycle) (figures 1 and 9) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 4.0 20 24 ???? ???? ???? ???? ???? 3.2 16 19 ???? ???? ???? ???? ???? 2.6 13 15 ??? ??? ??? ??? ??? mhz ???? ???? ???? ???? ???? t plh , t phl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, clock to q (figures 1 and 9) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 230 46 39 ???? ???? ???? ???? ???? 290 58 49 ???? ???? ???? ???? ???? 345 69 59 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? ???? t plh , t phl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, clock to carry out (figures 2 and 9) ???? ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? ??? 230 46 39 ???? ???? ???? ???? ???? ???? 290 58 49 ???? ???? ???? ???? ???? ???? 345 69 59 ??? ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t plh , t phl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, reset to q (figures 3 and 9) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 230 46 39 ???? ???? ???? ???? ???? 290 58 49 ???? ???? ???? ???? ???? 345 69 59 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t plh ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, reset to carry out (figures 3 and 9) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 230 46 39 ???? ???? ???? ???? ???? 290 58 49 ???? ???? ???? ???? ???? 345 69 59 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? ???? t plh , t phl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, clock enable to q (figures 4 and 9) ???? ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? ??? 250 50 43 ???? ???? ???? ???? ???? ???? 315 63 54 ???? ???? ???? ???? ???? ???? 375 75 64 ??? ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t plh , t phl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, clock enable to carry out (figures 5 and 9) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 250 50 43 ???? ???? ???? ???? ???? 315 63 54 ???? ???? ???? ???? ???? 375 75 64 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t tlh , t thl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum output transition time, any output (figures 8 and 9) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 75 15 13 ???? ???? ???? ???? ???? 95 19 16 ???? ???? ???? ???? ???? 110 22 19 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? c in ????????????????? ????????????????? ????????????????? ????????????????? maximum input capacitance ???? ???? ???? ???? e ??? ??? ??? ??? 10 ???? ???? ???? ???? 10 ???? ???? ???? ???? 10 ??? ??? ??? ??? pf notes: 1. for propagation delays with loads other than 50 pf , see chapter 2 of the motorola highspeed cmos data book (dl129/d). 2. information on typical parametric values can be found in c hapter 2 of the motorola highspeed cmos data book (dl129/d). c pd power dissipation capacitance (per package)* typical @ 25 c, v cc = 5.0 v pf c pd power dissipation capacitance (per package)* 35 pf * used to determine the noload dynamic power consumption: p d = c pd v cc 2 f + i cc v cc . for load considerations, see chapter 2 of the motorola highspeed cmos data book (dl129/d).
MC74HC4017 motorola highspeed cmos logic data dl129 e rev 6 4 timing requirements (input t r = t f = 6 ns)t ???? ???? ???? ???? symbol ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? guaranteed limit ??? ??? ??? ??? unit ???? ???? ???? ???? ???? symbol ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? ???? v cc v ??? ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? ???? 85 c ???? ???? ???? ???? ???? 125 c ??? ??? ??? ??? ??? unit ???? ???? ???? ???? ???? t su ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum setup time, clock enable to clock (figure 6) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 50 10 9 ???? ???? ???? ???? ???? 65 13 11 ???? ???? ???? ???? ???? 75 15 13 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t su ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum setup t ime, clock enable to clock (inhibit count) (figure 6) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 50 10 9 ???? ???? ???? ???? ???? 65 13 11 ???? ???? ???? ???? ???? 75 15 13 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t h ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum hold time, clock to clock enable (figure 6) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 50 10 9 ???? ???? ???? ???? ???? 65 13 11 ???? ???? ???? ???? ???? 75 15 13 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t rec ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum recovery time, reset to clock (figure 7) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 100 20 17 ???? ???? ???? ???? ???? 125 25 21 ???? ???? ???? ???? ???? 150 30 26 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t w ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum pulse width, clock input (figure 2) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 80 16 14 ???? ???? ???? ???? ???? 100 20 17 ???? ???? ???? ???? ???? 120 24 20 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? ???? t w ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum pulse width, reset input (figure 3) ???? ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? ??? 80 16 14 ???? ???? ???? ???? ???? ???? 100 20 17 ???? ???? ???? ???? ???? ???? 120 24 20 ??? ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t w ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? minimum pulse width, clock enable input (figure 4) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 80 16 14 ???? ???? ???? ???? ???? 100 20 17 ???? ???? ???? ???? ???? 120 24 20 ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? t r , t f ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum input rise and fall times (figure 1) ???? ???? ???? ???? ???? 2.0 4.5 6.0 ??? ??? ??? ??? ??? 1000 500 400 ???? ???? ???? ???? ???? 1000 500 400 ???? ???? ???? ???? ???? 1000 500 400 ??? ??? ??? ??? ??? ns note: information on typical parametric values can be found in chapter 2 of the motorola highspeed cmos data book (dl129/d). function table clock clock enable reset output state* l x l no change x h l no change x x h reset counter, q0 = h, q1 q9 = l, c0 = h l l advance to next state x l no change x l no change h l advance to next state x = don't care * carry out = h for q0, q1, q2, q3, or q4 = h; carry out = l otherwise. pin descriptions inputs clock (pin 14) counter clock input. while clock enable is low, a lowto high transition on this input advances the counter to its next state. reset (pin 15) asynchronous counter reset input. a high level at this input initializes the counter and forces q0 and carry out to a high, q1q9 are forced to a low level. clock enable (pin 13) activelow clock enable input. a low level on this input al - lows the device to count. a high level on this input inhibits the counting o peration . t hi s i npu t m a y a ls o b e u se d a s a negativeedge c loc k i nput . u sin g c loc k ( pi n 1 4 ) a s a n activehigh enable pin. outputs q0 q9 (pins 3, 2, 4, 7, 10, 1, 5, 6, 9, 11) decoded decade counter outputs. each of these outputs is high for one clock period only. carry out (pin 12) cascading output pin. this output is used either as a cas - cading output or a symmetrical dividebyten output. this output goes low when a count of five is reached and high when the counter advances to zero or when reset. when the counters are cascaded this output provides a risingedge signal for the clock input of the next counter stage.
MC74HC4017 highspeed cmos logic data dl129 e rev 6 5 motorola switching waveforms t r t f 90% 50% 10% v cc gnd t thl t phl t plh 1/f max t tlh q1q9 q0, carry out q t su q0 q9, carry out t rec figure 1. figure 2. figure 3. figure 4. figure 5. figure 6. figure 7. figure 8. clock enable carry out reset clock clock clock enable clock clock enable carry out reset clock 90% 50% 10% v cc gnd v cc gnd v cc gnd v cc gnd 50% 50% t w t w t plh t phl t w t plh t phl 90% 10% t thl t tlh 50% 50% 50% 50% valid t h v cc gnd v cc gnd v cc gnd v cc gnd v cc gnd 50% 50% 50% 50% t phl t plh q 50% t plh 50% 50% t w t phl * includes all probe and jig capacitance figure 9. test circuit c l * test point device under test output
MC74HC4017 motorola highspeed cmos logic data dl129 e rev 6 6 timiing diagram clock enable carry out reset clock q0 q1 q2 q3 q4 q5 q6 q7 q8 q9
MC74HC4017 highspeed cmos logic data dl129 e rev 6 7 motorola 15 reset clock clock enable q0 carry out 3 2 4 7 1 5 6 9 expanded logic diagram d q c q r 14 13 d q c q r d q c q r d q c q r d q c q r q1 q2 q3 q4 q5 q6 q7 q8 q9 11 12 10
MC74HC4017 motorola highspeed cmos logic data dl129 e rev 6 8 osc. (no feedback required) 1/6 hc04 output buffer (optional to prevent spurious reset.) v cc hc4017 q5 q1 q0 q2 q6 q7 q3 gnd reset clock carry out q9 q4 q8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 9 10 typical applications figure 10. 2 through 10 circuit clock enable c r ce q0 q1 q8 q9 figure 11. counter expansion 8 decoded outputs hc08 first stage intermediate stages v cc 4 8 5 2 6 7 3 hc4017 hc4017 hc4017 clock 8 decoded outputs 9 decoded outputs r r hc08 last stage c ce q0 q1 q8 q9 c ce q1 q8 q9 figure 10 shows a divide by 2 through 10 circuit using one hc4017. please note that since reset is asynchronous, the output pulse widths are narrow. figure 1 1 shows a technique for cascading the counters to extend the number of decoded output states. decoded outputs are sequential within each stage and from stage to stage, with no dead time (except propagation delay).
MC74HC4017 highspeed cmos logic data dl129 e rev 6 9 motorola outline dimensions n suffix plastic package case 64808 issue r min min max max inches millimeters dim a b c d f g h j k l m s 18.80 6.35 3.69 0.39 1.02 0.21 2.80 7.50 0 0.51 19.55 6.85 4.44 0.53 1.77 0.38 3.30 7.74 10 1.01 0.740 0.250 0.145 0.015 0.040 0.008 0.110 0.295 0 0.020 0.770 0.270 0.175 0.021 0.070 0.015 0.130 0.305 10 0.040 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of leads when formed parallel. 4. dimension b does not include mold flash. 5. rounded corners optional. 2.54 bsc 1.27 bsc 0.100 bsc 0.050 bsc a b 1 8 9 16 f h g d 16 pl s c t seating plane k j m l t a 0.25 (0.010) m m 0.25 (0.010) t b a m s s min min max max millimeters inches dim a b c d f g j k m p r 9.80 3.80 1.35 0.35 0.40 0.19 0.10 0 5.80 0.25 10.00 4.00 1.75 0.49 1.25 0.25 0.25 7 6.20 0.50 0.386 0.150 0.054 0.014 0.016 0.008 0.004 0 0.229 0.010 0.393 0.157 0.068 0.019 0.049 0.009 0.009 7 0.244 0.019 1.27 bsc 0.050 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 1 8 9 16 a b d 16 pl k c g t seating plane r x 45 m j f p 8 pl 0.25 (0.010) b m m d suffix plastic soic package case 751b05 issue j how to reach us: usa/europe : motorola literature distribution; japan : nippon motorola ltd.; tatsumispdjldc, toshikatsu otsuki, p.o. box 20912; phoenix, arizona 85036. 18004412447 6f seibubutsuryucenter, 3142 tatsumi kotoku, tokyo 135, japan. 0335218315 mfax : rmf ax0@email.sps.mot.com touchtone (602) 2446609 hong kong : motorola semiconductors h.k. ltd.; 8b tai ping industrial park, internet : http://designnet.com 51 ting kok road, tai po, n.t., hong kong. 85226629298 motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability , including without limitation consequential or incidental damages. at ypicalo parameters can and do vary in dif ferent applications. all operating parameters, including at ypicalso must be validated for each customer application by customer ' s technical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur . should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly , any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/af firmative action employer . MC74HC4017/d
? codeline

▲Up To Search▲

Price & Availability of MC74HC4017

	To Download MC74HC4017 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .